Traffic Spikes for ALL Vehicles

TireShark™ Traffic Spikes – Unlimited Weight

Get stronger spikes than you need. Be prepared for all axle weights. These are the traffic spikes for ALL vehicles! By installing these traffic spikes into the ground they can withstand all weights and all vehicles (at 5 MPH MAX).

In Ground Traffic Spikes

Model 7500 – For All Vehicles & Weights

In-ground flush mount traffic spikes transfer the weight of the vehicle directly to the road or driveway. These are great traffic spikes for ALL vehicle weights. It’s important that you limit traffic to 5 MPH to avoid tire damage, as well as damage to the traffic spikes system. Protect your investment by limiting traffic speeds with signs and speed bumps.

Many highways allow a maximum of 20,000 pounds per axle without a special permit. Most rear tractor and trailer axles support 34,000 pounds per axle maximum. Entire tractor/trailer weights, combined and loaded typically weigh no more than 80,000 pounds. Our traffic spikes are designed to take a higher weights, helping them to resist abuse. All our bearing surfaces in the traffic spikes are 100% replaceable because you should be able to replace parts, for decades of use.

PRO TIP: Drivers tend to ignore posted speeds. Buy traffic spikes and tire shredders that are stronger than you need! Of course, you need to properly direct traffic using bollards, curbs, and speed bumps. In addition, use speed bumps before AND after the location installation of the traffic spikes. After any excess speed event, and a few times per year, open the system and inspect for damage of replaceable parts and clean debris out. Following this, apply a bearing grease to rotating assemblies for continued performance. Eventually, bearing surfaces will wear, along with the shaft that has the points attached, and these can be easily replaced. Simply call or email us for traffic spikes replacements. Visit this site to learn more about spike strips: https://en.wikipedia.org/wiki/Spike_strip

Call Stacey at (800)988-3308 email: GR8MFG@HushMail.com

OR

Fill out the hassle free traffic spikes price quote form!

 

 

Maintain Traffic Spikes after snow storms.

Traffic Spikes damage from snow plow.
Maintain Traffic Spikes after snowing.

Snow Plows can damage Traffic Spikes. Repair damage and remove sediment.

Maintain Traffic Spikes after snowing. Make sure to inspect your parking lot’s traffic spikes after the snow season. Sometimes snow plow crews run over traffic spike systems. Heavy metal snow plow blades cause damage. Damaged traffic spikes may have been in the vertical position when struck by a snow plow. Remove TireShark™  Traffic Spikes prior to snow removal. Warn snow plow operators about traffic spike locations so that damage can be avoided. Install heating elements and thermostats into TireShark™ Traffic Spikes. Melt ice or snow during storms. Prevent ice build-up which can hinder proper operation. Typically, snow plow crews can manually shovel the snow that is nearest a traffic spike system. Avoid the possibility of damage altogether.

How to maintain TireShark™ Traffic Spikes after snow season…

Remove the top plate to inspect the welded steel rows of traffic spikes to maintain Traffic Spikes after snowing. Pay attention to removal of sediment and debris that may have built up during the winter. Study how the traffic spike section pivots within its bearings. Ensure easy rotation by making sure that the rotating spike shaft is still rounded and able to pivot within the bearings. Make sure that the bearing surfaces (hole) are still round and not egg-shaped. Make sure to apply axle grease to the contact area between the end of the traffic spike rotation shaft and the hole in the bearing plates. Check to make sure that the springs are fully functioning without breaks.

If any of these parts appear to be out of round, bent, broken or deteriorated, replace them immediately. We always have replacement parts and springs available to ship to you quickly. We recommend that you always have replacement parts for these wear-items in stock for immediate replacement so that you can always keep your traffic spike system up and running properly in your parking lot.

Perimeter Security Traffic Spikes

Perimeter Security Traffic Spikes secure fencing. Therefore, ideal for airports, prisons, and sensitive military and corporate locations.

Perimeter Security Traffic Spikes reduce chances of intrusion.

In addition to fencing, use these to secure the outside of corporate parking lots, airports, and prisons. On the whole, these types of heavy duty exterior perimeter traffic spikes are easy to install along fencing.

To conclude, these are designed to stop vehicles that penetrate the outside. Use these along all exterior fencing for your secure location for better results.

 

Visit this website for more information about types of items: https://en.wikipedia.org/wiki/Spike_strip

Contact Stacey for more information about perimeter security spikes.

 

Steel Speed Bumps

Steel Speed Bumps last even longer than rubber versions and are easy to install.

Steel Speed Bumps

All in all, these are great for Parking Lots, Parking Garages, and Alleys

Surprisingly, they can be removed for snowplow activity during winter.

Specifications:

Length: 3 Feet

Width: 18.5 Inches

Height: 2.25 Inches

 

Visit to learn more about speed bumps: https://en.wikipedia.org/wiki/Speed_bump

Visit Home to get back to the beginning of more information: https://www.trafficspikes.com/

Call Today! (800)988-3308

 

 

 

Orange Traffic Posts / Traffic Delineators

Heavy Duty Posts & Bases (Traffic Delineators)

Use these portable traffic posts (traffic delineators) to direct the flow of traffic along with your access control system.

Portable Traffic Delineators

In stock and ready for immediate shipment

Product Info

Our solid, 100% post-consumer recycled tire rubber bases are designed for stability, are resistant to the elements, do not crumble, and meet EPA specifications. Bases on this page can be personalized to your specifications for hole size, name, phone number, handle, vertical panel configuration, and thickness. You can create a whole new product, 1″ to 4″ thick, up to 72″ in length, and up to 48″ wide.

Our posts and bases interchange with most others on the market.

4” Diameter Posts

28” and 42”, safety orange.
Two, 3” white, high intensity reflective bands.
Open-Top, Bent T-Top.

Hexagonal Bases

18″ side to side – 21″ point to point
B8 1″ thick, 8 pounds
B12 1-1/8″ thick, 12 pounds
B18 1-3/4″ thick, 18 pounds

Call Stacey for a price quote! (800)988-3308

Email: GR8MFG@HushMail.com

Improve safety with Traffic Spikes

Traffic Spikes improve safety in parking lots and garages.

Traffic Spikes improve safety – Surface Mount

TireShark™ Traffic Spikes Ultra Low Profile Surface Mount One Way Traffic Control Surface Mounted

TireShark™ One-Way Traffic Spike System

Models: 2500, 3750, 5000 SpikeZilla™

Hot rolled steel, non-welded deck for durability. Laser cut parts are formed using computerized brakes. Easy to install traffic spikes. All bearings are easily replaceable for years of service. Powder Coated. Choice of Safety Red Or OSHA Yellow. Surface mounted. No digging, no mess, no wait. You can install on concrete or asphalt. Traffic Spikes improve safety.

How to Install Surface Mounted Traffic Spikes

The installation is so easy that many handymen can handle it. Complete the job in just a few hours. Normally, licensed contractors are called to perform the installation of one way traffic spike systems. More importantly, Traffic Spikes improve safety.

Install Traffic Spikes on Concrete

Use concrete anchors to mount the traffic spikes on the concrete driveway or road.

Install Traffic Spikes on Asphalt

Use two part epoxy to mount the traffic spikes on the asphalt surface.

PRO TIP: It is important to install these units with a catalyzed adhesive, such as a two part construction grade epoxy. We can supply this material to you, just mention it when you contact us. If you simply use construction adhesive (like air-dry adhesive) you risk allowing the units to be stolen or loosen more easily.

The competing model doesn’t have replaceable parts. That makes NO sense! That’s why we make it easy for you to replace parts instead of replacing the whole system.

 

Apartment / HOA Traffic Spikes

TireShark™ Traffic Spikes

TireShark™ Model 2500 Traffic Spikes Traffic Control System Traffic Spikes For APARTMENT HOATireShark™ Model 2500 can handle 80,000 pounds per axle maximum, at 5 mph. Ultra-low Deck Height & Strength make it great for residential and garage security. Save cost and easily install with these surface mounted traffic spikes. No digging, no mess, and no wait! Use these traffic spikes for apartment complex, HOA communities, and garage complexes!

TireShark™ Traffic Spikes Ultra Low Profile Surface Mount One Way Traffic Control Surface Mounted

Model 2500 – Traffic Spikes for Apartment / HOA

TireShark™ Surface Mount Traffic Spikes: Powder Coated, Weld-Free Decking, Zinc-Free, & Exclusive Nite-Bite™ Reflective Tire Spike Tips. All bearing surfaces are super easy to replace! So you don’t have to replace the whole system when you have unavoidable wear and tear. Get decades of use out of our traffic spikes.

Specifications – TireShark™ Traffic Spikes – Model 2500

Force required to form this steel is 57.5 tons. 1/4 inch plate steel. 1 3/4 inch deck height. 2 inches spike height adds to the overall height of 3 3/4 inches. Recommended for vehicles up to 80,000 pounds per axle maximum at 5 mph. It is important to limit the traffic to speeds of 5 mph. Reflective signage as well as speed bumps can be helpful to slow down traffic.

Many highways allow a maximum of 20,000 pounds per axle without any special permits. Most rear tractor and trailer axles are designed to support 34,000 pounds per axle maximum. Entire tractor/trailer weights, combined and loaded, typically weigh no more than 80,000 pounds. Our traffic spikes are designed to take higher weights, therefore helping them to resist abuse.

TireShark™ Surface Mount Traffic Spikes Low Deck Height Heavy DutyUltra-low Deck Height. At only 1 3/4” in height, you’ll never have a serious contact issue between your Porsche, Audi, or Corvette. The lowest typical sports car from the factory has a clearance of 4” from the ground as seen in Audi sports cars. Many sports cars are at least an inch higher than that! This image also shows the overall spike height of 3 3/4”, standard. You can choose an overall spike height of 3 1/2”, free of charge, if you’d like to further minimize the chances of contact with air dams, etc.

PRO TIP: Drivers tend to ignore posted speeds. Buy traffic spike tire shredders that are stronger than you need!

Call Stacey at (800) 988-3308 email: GR8MFG@HushMail.com

OR

Fill out the hassle free price quote form!

Corporate / Airport Traffic Spikes

Corporate / Airport Traffic Spikes improve security.

TireShark™ Traffic Spikes

Model 3750 can handle cars up to 90,000 lbs per axle  (5 mph), even full semi trucks. Great for corporate security because it’s 3/8″ plate steel. Use these traffic spikes for corporate offices / headquarters, airports, and car rentals. Google HQ has used TireShark™ to secure their corporate offices. They were happy with the quality of TireShark™ because they have constant heavy traffic.

Model 3750 – for Corporate / Airport

TireShark™ Surface Mount Traffic Spikes: Powder Coated, Weld-Free Decking, Zinc-Free, & Exclusive Nite-Bite™ Reflective Tire Spike Tips. All bearing surfaces are super easy to replace! So you don’t have to replace the whole system when you have unavoidable wear and tear. Get decades of use out of our traffic spikes.  Save cost with these surface mounted traffic spikes. No digging, no mess, and no wait!

 

Specifications – TireShark™ Traffic Spikes – Model 3750

Force required to form this steel is 63.5 tons. 3/8 inch plate steel. 2 inch deck height. Recommended for vehicles up to 90,000 pounds per axle maximum at 5 mph. It is important to limit the traffic to speeds of 5 mph. Reflective signage as well as speed bumps can be helpful to slow down traffic.

Many highways allow a maximum of 20,000 pounds per axle without any special permits. Most rear tractor and trailer axles are designed to support 34,000 pounds per axle maximum. Entire tractor/trailer weights, combined and loaded, typically weigh no more than 80,000 pounds. Our traffic spikes are designed to take higher weights, therefore helping them to resist abuse.

U.S. Military and Government facilities use this model of heavy duty traffic spikes because of the strength and longevity. If you are interested in placing an order for traffic spikes through a GSA Contract Holder, click here.

 

PRO TIP: Drivers tend to ignore posted speeds. Buy traffic spike tire shredders that are stronger than you need!

See our Instructions & Drawings for more information:

How To Install Surface Mount Traffic Spikes

 

Call Stacey at (800) 988-3308 email: GR8MFG@HushMail.com

OR

Fill out the hassle free price quote form!

Military Traffic Spikes

Military Traffic Spikes help to secure the nation.

TireShark™ Traffic Spikes

TireShark™ Model 5000 SpikeZilla™ Heavy Duty Traffic Spikes for MilitaryThis is the world’s strongest system (maximum 150,000 lbs per axle). 1/2 inch plate steel. Made in USA. Hot rolled steel, non-welded deck. Laser cut parts, formed using computerized brakes. TireShark™ Surface Mount Traffic Spikes: Powder Coated (Choice of Safety Red or OSHA Yellow), Weld-Free Decking, Zinc-Free, & Exclusive Nite-Bite™ Reflective Tire Spike Tips. All bearing surfaces are super easy to replace! So you don’t have to replace the whole system when you have unavoidable wear and tear. Get decades of use out of our traffic spikes.

Model 5000 – Traffic Spikes for Military / Government

TireShark™ Model 5000 SpikeZilla™ is great for military grade security. Use these heavy duty traffic spikes for military and government offices and facilities. You can purchase these traffic spikes for military or government through Wrigglesworth Enterprises, a GSA Contract Holder.

Steel End Cap pictured below: 1/2” thick TireShark™ 5000’s end cap, fitted against the end of a spike section.

Specifications – TireShark™ SpikeZilla™ – Model 5000

Force required to form this steel is 90 tons. 1/2 inch plate steel. 2 1/4 inch deck height. Recommended for vehicles up to 150,000 pounds per axle maximum at 5 mph. It is important to limit the traffic to speeds of 5 mph. Reflective signage as well as speed bumps can be helpful to slow down traffic.

Many highways allow a maximum of 20,000 pounds per axle without any special permits. Most rear tractor and trailer axles are designed to support 34,000 pounds per axle maximum. Entire tractor/trailer weights, combined and loaded, typically weigh no more than 80,000 pounds. Our traffic spikes are designed to take higher weights, therefore helping them to resist abuse.

PRO TIP: Drivers tend to ignore posted speeds. Buy traffic spike tire shredders that are stronger than you need!

See our Instructions & Drawings for more information:

How To Install Surface Mount Traffic Spikes

Traffic Spikes for U.S. Government:

GSA 51V: GS-21F-0015X
GSA 84: GS-07F-097GA
MRO FSSI: GS-23F-BA014
JANSAN FSSI: GS-07F-BA399
DHS PPE: HSHQDC-15-A-00018
DUNS # 612878772
CAGE CODE # 4HQD0
GSA # GS-21F-0015X

Women Owned Small Business Certified

Request a quote from Wrigglesworth Enterprises -> CLICK HERE

 

Heavy Duty Car Stop

Heavy Duty Car Stop last longer and reduce damage.

Heavy Duty Car Stop / Rubber Parking Curb

heavy duty car stop parking curb 550

Installation Steps
  1. For installations on uneven surfaces: Cut away rubber on the bottom of the product so that it becomes flush with the ground.
  2. Apply adhesive to the bottom of the heavy duty car stop for extra strength.
  3. Install on Asphalt: 14” x ½” rebar spike and washer for asphalt installation of all products.

Install on Concrete: 6” lag (screw, washer, and shield) for concrete installation of Car Stops.

 

Materials Needed for Installation:

·Provided Installation Hardware (comes included with heavy duty car stop. Call to order: (520)303-4444)

·Utility knife (if applying to an uneven surface – used for cutting away rubber if needed)

Pro-Tip:

Use 10 ounces of adhesive for glue down applications and so hardware won’t work loose

Parking Safety

Dependable and maintenance free!

Tough, recycled tire rubber is resistant to
weather, salt, moisture, UV, oil, and temperature. Made in the USA. Prompt shipping. Will not warp, chip, or crack. Easy, one person installation (instructions included). Installation hardware is available.

Our answer to the growing demand for lightweight, durable, made in USA Car Stops! (or Parking Curbs, Parking Bumpers, Wheel Stops or Parking Blocks… or whatever name you prefer for them!)

They will not chip or crack like concrete, nor warp like plastic can.

ST-6′ 4 holes, 8 stripes, 40 lbs.

ST-3′ 2 holes, 4 stripes, 20 lbs.

Permanent reflective striping – no painting!

Reflective stripes are made of road marking tape. Bonded stripes are available in yellow, white, blue or none

Ideal for parking lots, garages, wall protection, and other parking applications.